Miller XMT 450 MPa with Aux. Power Part#907479001

Description

Miller XMT® 450 MPa Multiprocess Welder With Auxiliary Power 907479001

The Miller® XMT® 450 MPa with Auxiliary Power is a true heavy industrial multiprocess welder capable of performing a wide range of Pulsed MIG welding, Stick welding, DC TIG welding Flux Cored Arc Welding and Air Carbon Arc Cutting and Gouging.

The XMT® 450 MPa has higher welding output for demanding applications. The Miller XMT® 450 MPa is the solution for applications where Multiprocess welding, Pulsed MIG, synergic control and brute power are needed. The XMT 450 MPa has the same exceptional arc performance, reliability and features as the XMT 350 MPa, but has additional Pulsed programs for .052 and 1/16 wires.

Comes complete with 115 volt, 10 amp receptacle installed on the rear of the welder.

Processes

• MIG Welding (GMAW)
• Pulsed MIG Welding (GMAW-P)
• DC TIG Welding (GTAW)
• Stick Welding (SMAW)
• Flux Cored Arc Welding (FCAW)
• Air Carbon Arc (CAC-A) Cutting and GougingApplications
  Construction
  Shipbuilding
  Railroad
  Truck and Trailer Manufacturing
  Fabrication
  Repair Shops
  Rental Fleets
  Power Generation PlantsFeatures
• MPa: M (MIG), P (Pulse), a (Advanced Arc Control). Advanced arc control enables an improved pulse welding arc. The operator has more control over puddle and bead characteristics using SharpArc™. In addition, the unit provides a more robust and stable arc at very low arc length, reducing heat input, and providing the ability to weld on a wider range of material thickness.
• What are some benefits of Synergic Pulsed MIG
  1. Easy to setup
  2. No more changing wire speed and then having to go back to reset the weld output.
• Auto Remote Sense™ enables unit to automatically use remote control if connected to remote control receptacle.
• SharpArc controls welding arc cone width in Pulsed MIG (GMAW-P) welding mode. If a gas is used other than what is listed on the Pulsed MIG welding program chart (below left), the SharpArc™ can be adjusted to help customize your arc to the gas being used. Lower SharpArc™ settings widen the arc cone, increase puddle fluidity and flattens the weld bead.
• Wind Tunnel Technology™ protects electrical components and PC oards from contamination.
• Fan-On-Demand™ cooling system operates only when needed, reducing noise, energy use and the amount of contaminants pulled through machine.
• Lift-Arc™ allows TIG starting without the use of high-frequency. Starts the arc without contaminating the weld with tungsten.
• Adaptive Hot Start™ increases the output amperage at the start of a weld if necessary, eliminating electrode sticking.
• Lightweight, aerospace-grade aluminum case offers protection with the benefit of reduced weight.
• Synergic Pulsed MIG – Adding the S-74 MPa Plus feeder or the XR-AlumaFeed™ feeder gives you the benefit of a Synergic Pulsed MIG system. As you increase/decrease the wire feed speed, the pulse parameters increase/decrease, matching the right amount of power output to match the wire speed.
• Inverter arc control technology provides greater puddle control for superior 6010 Stick electrode performance, and outstanding MIG weld performance.
• Line voltage compensation keeps welding output constant even if input power varies by +/-10%.
• Process selector switch reduces the number of control setup combinations without reducing any features.
• Large, dual digital meters are easy to view and are presettable.
  
• Insight Core Optional Welding Intelligence system compatible – XMT CC/CV models are Insight capable to monitor weld voltage, amperage, and arc-time and percentage while MIG or Flux-cored arc welding.
• 115 VAC auxiliary power provides 10 amps of circuit-breaker-protected power for water circulators, etc.

  PLUS – get a FREE Miller® T94i™ ClearLight™ 2.0 auto-darkening welding helmet with purchase of a Miller® XMT® 450 MPa welder. While supplies last. (No substitutions allowed.)